University of Tabriz
Islamic World Science Citation Center (ISC)
1.

A Neural-Network Model for Prediction of Damage Initiation Force in Mode 1 Delamination of Composite Materials

Pages 1-7
Zohreh Ebrahimi; Mahmud Bahrami Rahnam
2.

Numerical Simulation of a Maisotsenko Cycle Heat Exchanger by Computational Fluid Dynamics

Pages 9-17
Mohsen Izadi; Saeed Naderi
3.

Analysis of tensile properties of hybrid nanocomposite based on epoxy/ glass fibers/ nano-silica

Pages 19-25
Faramarz Ashenai Ghasemi; Ismail Ghasemi
4.

Experimental study of the effects of accelerated flow on the fluctuation, parameters and high-order values of velocity in the wake of a bluff body

Pages 27-36
Vahid Barzanooni; Abdol Amir Bak Khoshnevis
5.

Numerical investigation on effect of geometrical parameters and rotor speed on leakage flow of gas turbine brush seal

Pages 37-45
Mohammad Bahadori; Saadat Zirak
6.

Two different methods of measuring ductile damage for stainless steel 316L

Pages 47-54
Moslem Bahrami; Farhad Haji Aboutalebi; Abolfazl Darvizeh; Reza Ansari Khalkhali
7.

Derivation of Airship Arodynamic Characteristics at high angles of attack

Pages 55-63
Javid Hoseinpour Zavie Jaki; AliReza A. R. Roudbari
8.

A parametric effectiveness and Temperature distribution investigation of three-fluid heat exchanger with three thermal communication

Pages 65-75
Reza Rastgar; Amir Farhang Sotoodeh; Majid Amidpour
9.

Investigation on Effects of Joints Design Geometry on the Weld Metal Metallurgical Transformations and Fracture Modes in the ASTM A-128 Hadfield Steel Welding Joints

Pages 77-85
Masoud Sabzi; Rougaiyeh Kalantaripour; Ahmad Monshi
10.

Experimental failure analysis of a reconditioned heavy crankshaft by welding process

Pages 87-93
Roohollah Sarfaraz; MohamadAli Ehteram; Keshvad Pourhasan
11.

Investigation of the Effect Mixed Hydrophilic and Hydrophobic Fibers in the Gas Diffusion Layer of a Polymer Electrolyte Membrane Fuel Cell

Pages 95-103
Esmaeil ShakeriNejad; Mohsen Nazari; Mohammad Hasan Kayhani
12.

Numerical investigation of the effect of air mal-distribution, aspect ratio and fin configuration on the corrugated louvered fin radiator performance and proposing an improved fin profile

Pages 105-114
Ali Shayegh; Saeid Kheradmand; Hossein Sadeghinasab
13.

Numerical low-velocity impact and structural damping analysis of a rectangular poroelastic plate

Pages 115-124
Mohammad Shariyat; Mohsen Jahangiri; Masoud Asgari
14.

Study on the effects of the injection pressure of an annulus nozzle and combustion chamber on the performance of a diesel engine

Pages 125-134
Mohamad Taghi Shervani-Tabar; Rasool Esmaelnajad; Seyed Esmail Razavi; Moharram Jafari
15.

Thermo-economic Analysis of the Solid Oxide Fuel Cell, Gas Turbine and Steam Turbine Hybrid System for Fuel Cell and Gas Turbine Direct and Indirect Connection

Pages 135-144
16.

Modeling and Simulation of a Piezoelectric Micro Flow Sensor with Micro Energy Harvester

Pages 145-154
Reza Safari; Amir Monemian Esfahani; Mohsen Bahrami
17.

Numerical Analysis of Thermal Multilayer Insulations with carbon nanofiber spacers

Pages 155-164
Seid Abbas Talebi; Amin Behzadmehr; Samira Payan
18.

Production of copper superhydrophobic surfaces with micro-nano structuring using an electrochemical process and coting with hydrophobic promoter

Pages 165-174
Hamid Reza Talesh Bahrami; Hamid Saffari; Ali Rostamnejad; Gholamreza Shahriari
19.

Optimization of an Axial Flow Compressor Performance with Change of Lean and Sweep Angles

Pages 175-182
Abolhasan Asgarshamsi
20.

Investigating the effect of presence of porous media in the micro combustion chamber on radiation efficiency

Pages 183-192
Hosein Faramarzpour; Kiumars Mazaheri; Alireza Alipoor; Ghader oliayi
21.

Numerical Simulation of Cavitation and Vapor Bubble Formed in Transient Mode for 3D Marine Diesel Engine Injector Nozzle

Pages 193-202
Mohammad Kamari; Bahman Asadi; Majid Satarche
22.

Experimental investigation of drilling 6061-T6 aluminum alloys under MQL and dry modes

Pages 203-211
Hadi Kiani; Nader Barari; Seyed Ali Niknam
23.

Numerical Analysis of Hyperthermia on the Damage of cancerous Tissue by injection of Magnetic nanoparticles under the Influence of External Magnetic Field

Pages 213-221
Mahdi Keyhanpour; Majid Ghasemi
24.

Reliability based topology optimization for structures with multiple load cases

Pages 223-227
Hamed Mohammadzadeh; Mohammad Hosein Abolbashari
25.

Simulation of aluminum profile extrusion considering the effect of lubricant

Pages 229-238
Saeed Mohammadzadeh; Mahsa Kharizi; Davoud Jalali Vahid
26.

Heat transfer intensification of shell-and-tube heat exchangers of the crude oil distillation unit in Imam Khomeini oil refining company

Pages 239-248
Rafat Mohammadi; AhmadReza Ghasemi; Hamed Safikhani
27.

An experimental study of mass transfer rate from the simple levels of water surface for forced and mixed convection regimes

Pages 249-255
Amir Reza Mamouri; Amin Jodat
28.

Design of optimal torque vectoring control system with predictive approach for improvement of stability and energy consumption in electric vehicle

Pages 257-267
Behrouz Najjari; Mehdi Mirzaei; Amin Tahouni
29.

Three-dimensional simulation of airflow in the human respiratory system

Pages 269-277
Amireh Nourbakhsh; Mortaza Bayareh
30.

Nano-metric Polishing of Optical Lenses by Magnetic Float Polishing (MFP)

Pages 279-287
Mehrdad Vahdati; Seyed Adel Ameli Kalkhoran
31.

Numerical Simulation of Hollow Fiber Membrane Bioreactor and Investigation of the Parameters Related to Animal Cells Culture

Pages 289-298
Sohrab Valadbeigy; Farzan Ghalichi; Reza Yegani; Ali Akbari
32.

Evaluation of DME/DME Integration as APNT for I.R. IRAN

Pages 299-303
Gasem Kahe; Mohammad Saberi Tavakkoli


Journal Management System. Powered by Sinaweb