شبیه‌سازی عددی پدیده کاویتاسیون و تشکیل حباب در حالت گذرا درهندسه سه‌بعدی نازل انژکتور موتور دیزل دریایی

[1]     Rouse H., and McNown., J.S., Cavitation and Pressure Distribution, Head Forms at Zero Angle of Yaw. Studies in Engineering, Bulletin, State University of Iowa Aemes, Iowa. 1948

[2]     Chen Y., Heister SD., A numerical treatmentfor attached cavitation. .J Fluids Eng; pp 8–13,1994

[3]     Singhal AK., Vaidya N., Leonard AD., Multidimensional simulation of cavitating flows using a PDF model for phase change .ASME Paper FEDSM97-3272, 1997.

[4]     Kunz RF., Chyczewski TS., Boger DA., Stinebring DR., Gibeling HJ, Multi-phase CFD analysis of natural and ventilated cavitation about submerged bodies. ASME Paper FEDSM99-7364, Proceedings of the Third ASME/ JSME Joints Fluids Engineering Conference, 1999.

[5]     Senocak KJ., Shyy TY., Computational methodologyfor the simulation of turbulent cavitating flows. The University of Florida. Lecoffre, Cavitation Bubble Trackers. (Book), 2001.S

[6]      Martynov B., Mason D J. and Heikal M R., Numerical simulation of cavitation flows based on their hydrodynamic similarity .The manuscript was accepted after revision for publication on 6 September, 2005

[7]     Dabiri S. and Sirignano W., A.., Cavitation in an orifice flow. J.    PHYSICS OF FLUIDS 19, 072112, 2007.

[8]     Dipl Ing., Daniele Suzzi., Diesel Nozzle Flow and Spray Formation: Coupled Simulations with Real Engine Validation. Institute of Aerospace Thermodynamics, pp1-6, 2009.

[9]     SABAU S. A., Adrian A.Y., BARHALESCU, Mihaela Luminita., OANTA, Emil, MODELING OF HIGH-PRESSURE FUEL INJECTION SYSTEMS. Annals of DAAAM & Proceedings of the 23rd International DAAAM Symposium, Volume 23, No.1, ISSN 2304-1382, 2012.

[10] Adrian J Butcher., Pavlos G Aleiferis and Dave Richardson., Development of a Real-size Optical Injector Nozzle for Studies of Cavitation, Spray Formation and Flash-Boiling at Conditions Relevant to Direct-Injectionspark-Ignition Engines. International J of Engine Research14 (6) 557–577, 2013.

[11] Vimal Kumar, Pathak and Sumit Gupta., STUDY OF NOZZLE INJECTOR PERFORMANCE USING CFD. International Journal of Recent advances in Mechanical Engineering (IJMECH) Vol.4, No.3, 2015.

[12] Zandi1 A.., Sohrabi S.., Shams M.., Influence of nozzle geometry and injection conditions on the cavitation flow inside a diesel injector. International Journal Automotive Engineering Vol. 5, Number 1, March, 2015.

[13] Phoevos Koukouvinis., Manolis Gavaises., Jason Li., Lifeng Wang., Large Eddy Simulation of Diesel injector including cavitation effects and correlation to erosion damage Fuel. 175 pp 26–39, 2016.

[14] Florijn J., Experimental Studies on the Performance of Catalytically Hydrotreated Fast Pyrolysis oil in a Stationary Diesel Engine. Acknowledged for assisting with the engine test. 2004.

[15] Payri R., Margot X., Salvador F J  Anumerical study of the influence of diselnozzle geometry on the inner cavitating flow.SAE Paper 01-0215, 2002.