مطالعه عددی رفتار لرزه‌ای قاب‌های فولادی سرد نورد شده با مهاربند K شکل

مقدم ح، "مهندسی زلزله مبانی و کاربرد"، ویرایش هفتم، نشر کتاب دانشگاهی، 1387.

Adham S, Avanessian V, Hart G, Anderson R, Elmlinger J, Gregory J, “Shear wall resistance of lightgage steel stud wall systems”, Earthquake Spectra, 1990, 6, 1-14.

AISI, “Standard for cold-formed steel framing- Lateral design”, Washington, D.C.: American Iron and Steel Institute, 2007.

“ANSYS® Academic Research”, 14.50, Ed., 2013.

AS/NZS4600., “Cold-formed steel structures”, Australian Building Codes Board, 2005.

B.S.S. Council, “FEMA-356, Prestandard and commentary for the seismic rehabilitation of buildings”, Federal Emergency Management Agency, Washington, DC, 2000.

B.S.S. Council, “FEMA 450, NEHRP Recommended Provisions for Seismic Regulations for New Buildings and Other Structures: Provisions/ Prepared by the Building Seismic Safety Council”, Building Seismic Safety Council, National Institute of Building Sciences, 2004.

Hibbitt H, Karlsson B, Sorensen P, ABAQUS/standard: User's Manual vol. 1: Hibbitt, Karlsson & Sorensen, 1998.

Lai SSP, Biggs JM, “Inelastic response spectra for aseismic building design”, Journal of the Structural Division, 1980, 106, 1295-1310.

Lim JB, Nethercot DA, “Finite element idealization of a cold-formed steel portal frame”, Journal of Structural Engineering, 2004, 130, 78-94.

Miranda E, Bertero VV, “Evaluation of strength reduction factors for earthquake-resistant design”, Earthquake spectra, 1994, 10, 357-379.

Moghimi H, Ronagh HR, “Better connection details for strap-braced CFS stud walls in seismic regions”, Thin-Walled Structures, 2009, 47, 122-135.

Newmark NM, Hall WJ, “Seismic design criteria for nuclear reactor facilities”, Building Practices for Disaster Mitigation, National Bureau of Standard, U.S. Report No. 46, 1973.

Rogers C, Hancock G, “Ductility of g550 sheet steels in tension-elongation measurements and perforated tests”, University of Sydney, 1996.

Schafer B, Peköz T, “Computational modeling of cold-formed steel: characterizing geometric imperfections and residual stresses”, Journal of Constructional Steel Research, 1998, 47, 193-210.

Sivakumaran K, Abdel-Rahman N, “A finite element analysis model for the behaviour of cold-formed steel members”, Thin-walled structures, 1998, 31, 305-324.

Zeynalian M, “Seismic performance of cold formed steel structures, and risk analysis and management for use in earthquake prone regions”, Ph.D, University of Queensland, 2012.

Zeynalian M, “Axial Compression Capacity of Cold Formed Steel C-Channel Single Stud Section”, presented at the 7th National Congress on Civil Engineering, University of Sistan and Baluchestan, Zahedan, Iran, 2013.

Zeynalian M, Ronagh H, “A numerical study on seismic characteristics of knee-braced cold formed steel shear walls”, Thin-Walled Structures, 2011, 49, 1517-1525.

Zeynalian M, Ronagh H, “A numerical study on seismic performance of strap-braced cold-formed steel shear walls”, Thin-Walled Structures, 2012, 60, 229-238.

Zeynalian M, Ronagh H, Hatami S, “Seismic characteristics of K-braced cold-formed steel shear walls”, Journal of Constructional Steel Research, 2012, 77, 23-31.