
تعداد نشریات | 45 |
تعداد شمارهها | 1,392 |
تعداد مقالات | 17,030 |
تعداد مشاهده مقاله | 54,955,848 |
تعداد دریافت فایل اصل مقاله | 17,437,240 |
ارزیابی آزمایشگاهی رفتار ماسه مسلح شده به ژئوگرید قرار گرفته بالای حفرات دوقلو | ||
نشریه مهندسی عمران و محیط زیست | ||
مقاله 5، دوره 55، شماره 118، خرداد 1404، صفحه 35-52 اصل مقاله (8.71 M) | ||
نوع مقاله: مقاله کامل پژوهشی | ||
شناسه دیجیتال (DOI): 10.22034/ceej.2024.59826.2313 | ||
نویسندگان | ||
پانته آ پزشکیان؛ میکائیل کاظم زاده؛ امیرعلی زاد* ؛ مریم یزدی | ||
گروه مهندسی عمران، دانشگاه آزاد اسلامی، واحد تهران مرکز، تهران | ||
چکیده | ||
مطالعه حاضر، به بررسی رفتار خاک ماسهای دارای حفرات دوتایی مسلح شده با ژئوگرید مقیاس شده تحت اثر بارگذاری استاتیکی بهصورت آزمایشگاهی میپردازد. تفاوت مهم مطالعه فوق در مقایسه با مطالعات مشابه انجام گرفته در زمینه تسلیح خاکهای بدون و با حفره، استفاده از مسلح کنندههای مقیاس شده است. تأثیر دانسیته نسبی خاک، فاصله افقی و عمق مدفونشدگی حفرات، فاصله عمودی لایههای مسلح کننده و عمق مدفونشدگی لایه اول مسلح کننده بر رفتار بار- نشست خاک مسلح شده و جابه جایی افقی حفرات مورد بررسی قرار گرفته است. جهت بررسی چگونگی شکلگیری گوههای گسیختگی، نحوه گسیختگی خاک زیر پی و میزان کرنش برشی پدید آمده در اثر اعمال بار در محل گوههای گسیختگی از روش سرعت سنجی تصویری ذرات (PIV) استفاده شده است. ارزیابی نتایج بهدست آمده نشان داد که با افزایش فاصله عمودی مسلح کنندهها و عمق مدفونشدگی لایه اول مسلح کننده، سربار قرار گرفته بر روی مسلح کنندهها و مقاومت اصطکاکی بین مسلح کنندهها و خاک ماسهای افزایش یافته و متعاقب آن ظرفیت باربری خاک ماسهای با حفرات دوتایی مسلح شده افزایش یافته است. همچنین، نتایج بیانگر این بود که تسلیح خاک متراکم با دو لایه ژئوگرید باعث افزایش ظرفیت باربری خاک ماسهای متراکم با حفرات دوتایی مسلح شده به میزان 8/51% در مقایسه با خاک ماسهای متراکم با حفرات دوتایی بدون مسلحکننده شده است. در نهایت، ارزیابی خروجیهای تحلیل PIV نشاندهنده این موضوع بود که نرخ کرنش برشی شکل گرفته در اثر بارگذاری در محل گوه گسیختگی زیر پی با افزایش تعداد لایهها و عمق مدفونشدگی لایه اول مسلح کننده، کاهش یافته است. | ||
کلیدواژهها | ||
ژئوگرید؛ ظرفیت باربری؛ حفرات دوقلو؛ خاک مسلح شده؛ دانسیته نسبی خاک | ||
سایر فایل های مرتبط با مقاله
|
||
مراجع | ||
Abu-Farsakh M, Chen Q Sharma R, “An experimental evaluation of the behavior of footings on geosynthetic-reinforced sand”, Soils and Foundations, 2013, 53, 335-348. https://doi.org/10.1016/j.sandf.2013.01.001 Anaswara S, Shivashankar R, “Study on behaviour of two adjacent strip footings on unreinforced/reinforced granular bed overlying clay with voids”, Geotechnical and Geological Engineering, 2021, 39, 1831-1848. https://doi.org/10.1007/s10706-020-01590-1 Asakereh A, Ghazavi M, Tafreshi SM, “Cyclic response of footing on geogrid-reinforced sand with void”, Soils and Foundations, 2013, 53, 363-374. https://doi.org/10.1016/j.sandf.2013.02.008 Ates B, Sadoglu E, “A quasi-2D exploration of optimum design settings for geotextile-reinforced sand in assistance with PIV analysis of failure mechanism”, Geotextiles and Geomembranes, 2023, 51, 418-436. https://doi.org/10.1016/j.geotexmem.2023.01.005 Baus R, Wang M, “Bearing capacity of strip footing above void”, Journal of Geotechnical Engineering, 1983, 109, 1-14. https://doi.org/(ASCE)0733-9410(1983)109:1(1) Chaabani W, Remadna MS, Abu-Farsakh M, “Numerical modeling of the ultimate bearing capacity of strip footings on reinforced sand layer overlying clay with voids”, Infrastructures, 2022, 8 (1), 3. https://www.mdpi.com/2412-3811/8/1/3 Chauhan VB, Kumar P, Keawsawasvong S, “Limit analysis solution for ultimate bearing capacity of footing resting on the rock mass with a circular void subjected to line loading”, Indian Geotechnical Journal, 2023, 53, 334-347. https://doi.org/10.1007/s40098-022-00676-2 Chen J, Guo X, Sun R, Rajesh S, Jiang S, Xue J, “Physical and numerical modelling of strip footing on geogrid reinforced transparent sand”, Geotextiles and Geomembranes, 2021, 49, 399-412. https://doi.org/10.1016/j.geotexmem.2020.10.011 Da Silva Burke T, Elshafie M, “Geosynthetic-reinforced soils above voids: Observation of soil and geosynthetic deformation mechanisms”, Geotextiles and Geomembranes, 2021, 49, 1-18. https://doi.org/10.1016/j.geotexmem.2020.02.013 Demirdöğen S, Gürbüz A, Yünkül K, “Performance of eccentrically loaded strip footings on geocell-reinforced soil”, Geotextiles and Geomembranes, 2024. https://doi.org/10.1016/j.geotexmem.2023.12.007 Feng S-J, Ai S-G, Chen H, Xie H-J, “An analytical method for predicting load acting on geosynthetic overlying voids. Geotextiles and Geomembranes, 2017, 45, 570-579. https://doi.org/10.1016/j.geotexmem.2017.07.007 Harshani H, Galindo-Torres S, Scheuermann A, Muhlhaus H, “Experimental study of porous media flow using hydro-gel beads and LED based PIV”, Measurement Science and Technology, 2016, 28, 015902. https://doi.org/10.1088/1361-6501/28/1/015902 Huckert A, Briançon L, Villard P, Garcin P, “Load transfer mechanisms in geotextile-reinforced embankments overlying voids: experimental and analytical approaches”, Geotextiles and Geomembranes, 2016, 44, 442-456. https://doi.org/10.1016/j.geotexmem.2015.06.005 Khalaj O, Davarifard S, Tafreshi SNM, Mašek B, “Cyclic response of footing with embedment depth on multi-layered geocell-reinforced bed”, IOP Conference Series: Earth and Environmental Science, IOP Publishing, 2016, 22015. https://doi.org/10.1088/1755-1315/44/2/022015 Khing K, Das B, Puri V, Cook E, Yen S, “The bearing-capacity of a strip foundation on geogrid-reinforced sand. Geotextiles and Geomembranes, 1993, 12, 351-361. https://doi.org/10.1016/0266-1144(93)90009-D Khosravi S, Karimpour-Fard M, Shahnazari H, Aminpour M, Nazem M, “Undrained bearing capacity of circular and square footings above centric and eccentric three-dimensional cavities”, International Journal of Geomechanics, 2024, 24, 04024104. https://doi.org/doi:10.1061/IJGNAI.GMENG-8835 Kou Y, Shukla SK, Mohyeddin A, “Effect of width of geosynthetic reinforcement within the granular cover on the load distribution over the tunnel lining”, Civil Infrastructures Confronting Severe Weathers and Climate Changes Conference, 2018, Springer, 52-59. Kumar P, Chauhan VB, “Behavior of footing resting above dual circular cavities in a rock mass: insights from an AFELA study”, International Journal of Geomechanics, 2024, 24, 04023248. https://doi.org/doi:10.1061/IJGNAI.GMENG-9036 Lai F, Chen F, Li D, “Bearing capacity characteristics and failure modes of low geosynthetic-reinforced embankments overlying voids”, International Journal of Geomechanics, 2018, 18, 04018085. https://doi.org/doi:10.1061/(ASCE)GM.1943-5622.0001206 MA Y, Yan G, Scheuermann A, Li L, Galindo-Torres S, Bringemeier D, “Discrete microbubbles flow in transparent porous media”, Unsaturated Soils: Research and Applications, CRC Press, 2020. Majidi A, Yazdi M, “Physical modeling of the effect of using scaled geosynthetic reinforcements on bearing capacity and settlement of strip footing”, International Journal of Geomechanics, 2023, 23, 04023093. https://doi.org/doi:10.1061/IJGNAI.GMENG-8141 Moghaddas Tafreshi S, Khalaj O, Halvaee M, “Experimental study of a shallow strip footing on geogrid-reinforced sand bed above a void”, Geosynthetics International, 2011, 18, 178-195. Moghaddas Tafreshi SN, Dawson AR, “A comparison of static and cyclic loading responses of foundations on geocell-reinforced sand”, Geotextiles and Geomembranes, 2012, 32, 55-68. https://doi.org/10.1016/j.geotexmem.2011.12.003 Moghaddas Tafreshi SN, Khalaj O, “Laboratory tests of small-diameter HDPE pipes buried in reinforced sand under repeated-load”, Geotextiles and Geomembranes, 2008, 26, 145-163. https://doi.org/10.1016/j.geotexmem.2007.06.002 Moghaddas Tafreshi SN, Sharifi P, Dawson AR, “Performance of circular footings on sand by use of multiple-geocell or -planar geotextile reinforcing layers”, Soils and Foundations, 2016, 56, 984-997. https://doi.org/10.1016/j.sandf.2016.11.004 Naftchali FM, Bathurst RJ, “Numerical modelling of reinforced fill over a void considering rate-dependent stiffness of the reinforcement”, Geotextiles and Geomembranes, 2024. https://doi.org/10.1016/j.geotexmem.2024.03.006 Sireesh S, Sitharam T, Dash SK, “Bearing capacity of circular footing on geocell–sand mattress overlying clay bed with void. Geotextiles and Geomembranes, 2009, 27, 89-98. https://doi.org/10.1016/j.geotexmem.2008.09.005 Tafreshi SM, Dawson A, “Behaviour of footings on reinforced sand subjected to repeated loading-Comparing use of 3D and planar geotextile”, Geotextiles and Geomembranes, 2010, 28, 434-447. https://doi.org/10.1016/j.geotexmem.2009.12.007 Tavakoli Mehrjardi G, Moghaddas Tafreshi SN, Dawson, AR, “Combined use of geocell reinforcement and rubber-soil mixtures to improve performance of buried pipes”, Geotextiles and Geomembranes, 2012, 34, 116-130. https://doi.org/10.1016/j.geotexmem.2012.05.004 Terzaghi K, Theoretical Soil Mechanics, 1943. Tizpa P, Chenari RJ, Payan M, “PFC/FLAC 3D coupled numerical modeling of shallow foundations seated on reinforced granular fill overlying clay with square void”, Computers and Geotechnics, 2023, 161, 105574. https://doi.org/10.1016/j.compgeo.2023.105574 Wang M, Badie A, “Effect of underground void on foundation stability. Journal of Geotechnical Engineering, 1985, 111, 1008-1019. https://doi.org/10.1061/(ASCE)0733-9410(1985)111:8(1008) White DJ, Take W, Bolton M, “Measuring soil deformation in geotechnical models using digital images and PIV analysis”, 10th International Conference On Computer Methods And Advances In Geomechanics, Citeseer, 2001, 997-1002. White D, Take W, “Particle image velocimetry (PIV) software for use in geotechnical testing”, University of Cambridge, Department of Engineering, 2002. White DJ, “An investigation into the behaviour of pressed-in piles”, University of Cambridge, 2002. White DJ, Take WA, Bolton MD, “Soil deformation measurement using particle image velocimetry (PIV) and photogrammetry”, Geotechnique, 2003, 53 (7), 619-631. https://doi.org/10.1680/geot.2003.53.7.619 Wu G, Zhao M, Zhao H, Xiao Y, “Effect of eccentric load on the undrained bearing capacity of strip footings above voids”, International Journal of Geomechanics, 2020, 20, 04020078. https://doi.org/doi:10.1061/(ASCE)GM.1943-5622.0001710 Yan G, Cheng Z, Ma Y, Scheuermann A, Li L, “Applying imaging technique to investigate effects of solute concentrations and gas injection rates on gas bubble generation”, Geofluids, 2022, 2046267. Yan G, Xu Y, Murgana V, Scheuermanna A, “Application of image analysis on two-dimensional experiment of ground displacement under strip footing”, Proceedings of GeoShanghai 2018 International Conference: Ground Improvement and Geosynthetics, 2018, Springer, 13-21. Yetimoglu T, Wu JT, Saglamer A, “Bearing capacity of rectangular footings on geogrid-reinforced sand”, Journal of Geotechnical Engineering, 1994, 120, 2083-2099. https://doi.org/10.1061/(ASCE)0733-9410(1994)120:12(2083) Zhao L, Huang S, Zeng Z, Zhang R, Tang G, Zuo S, “Study on the ultimate bearing capacity of a strip footing influenced by an irregular underlying cavity in karst areas”, Soils and Foundations, 2021, 61, 259-270. https://doi.org/10.1016/j.sandf.2020.09.011 Zhao L, Huang S, Zhang R, Zuo S, “Stability analysis of irregular cavities using upper bound finite element limit analysis method”, Computers and Geotechnics, 2018, 103, 1-12. https://doi.org/10.1016/j.compgeo.2018.06.018 Zhou H, Zheng G, He X, Xu X, Zhang T, Yang X, “Bearing capacity of strip footings on c-φ soils with square voids”, Acta Geotechnica, 2018, 13, 747-755. https://doi.org/10.1007/s11440-018-0630-0 | ||
آمار تعداد مشاهده مقاله: 321 تعداد دریافت فایل اصل مقاله: 34 |